Cooling process of the gear on Transient Thermal (Ansys Workbench)

on

 Transient Thermal module is a type of analysis that allows you to simulate the temperature changes and heat transfer in a system over time. It is useful for studying problems that involve time-dependent thermal loads, such as heat treatment, electronic cooling, engine heating, etc.

In Transient Thermal module, you need to specify the initial temperature distribution, the material properties (such as density, specific heat, and thermal conductivity), the boundary conditions (such as convection, radiation, and heat flux), and the time steps for the analysis. The module will solve the heat conduction equation for each time step and generate the results for the temperature, heat flux, heat transfer coefficient, etc.

You can also use Transient Thermal module to perform coupled thermal-structural analysis, where the thermal results are transferred to a structural analysis to calculate the thermal stresses and strains. This can help you evaluate the effects of thermal expansion, contraction, and deformation on your system.

If you want to learn more about Transient Thermal module in Ansys workbench, you can check out some of these resources:

- [Intro to Transient Thermal Analysis - ANSYS Innovation Courses](^5^): This is a PDF document that introduces the basics of transient thermal analysis and the governing equation.

- [Transient Thermal Analysis in ANSYS](^1^): This is a YouTube video that shows you how to do a transient thermal analysis in Ansys workbench with an example problem.

- [Transient heat transfer analysis using ANSYS workbench](^2^): This is another YouTube video that demonstrates how to perform transient heat transfer analysis using Ansys workbench with a different example problem.

I hope this helps you understand what is Transient Thermal module in Ansys workbench.

Source:

(1) Intro to Transient Thermal Analysis - ANSYS Innovation Courses. https://courses.ansys.com/wp-content/uploads/2020/05/Lesson-1-Introduction-to-transient-analysis.pdf.

(2) Transient Thermal Analysis in ANSYS - YouTube. https://www.youtube.com/watch?v=4Jj0s-DAvfg.

(3) Transient heat transfer analysis using ANSYS workbench. https://www.youtube.com/watch?v=wJW6IIovyPo.

(4) ANSYS Transient Thermal Tutorial - Convection of a Bar in Air. https://www.youtube.com/watch?v=fd0xQQ1IGvw.

(5) Setup Transient Thermal Analysis - ANSYS Innovation Courses. https://courses.ansys.com/index.php/courses/radiation-between-surfaces/lessons/physics-setup-lesson-5-16/topic/setup-transient-thermal-analysis/.

Comments

Post a Comment

Popular POSTS

Image

Quick Tip: How to fix Error: GENERAL-CAR-CDR in Ansys (Fluent)

 The error message Error: GENERAL-CAR-CDR: invalid argument [1]: improper list means that there is a problem with the scheme code or the UDF (user-defined function) in your case or data file . Some possible solutions are: Save the case and data file and try to reopen it. Reset the Fluent Setup tab and try opening the mesh. Remesh the geometry and reopen in Fluent. Change the material definition from “Solid” to “Fluid” in Design Modeler. Change the transient to steady if you are using evaporation-condensation as the phase interaction mechanism. Check the syntax of your UDF and make sure it follows the new rules in Fluent 6.2.16 or later. I hope this helps you resolve the error. If you need more assistance, please visit the Ansys Learning Forum or contact Ansys Support . Have a nice day! 😊 Sources: 1. smartadm.ru 2. cfd-online.com 3. forum.ansys.com 4. forum.ansys.com In Polish  BÅ‚Ä…d: GENERAL-CAR-CDR oznacza, że wystÄ…piÅ‚ problem z kodem Scheme w programie Ansys Fluent. Scheme to jÄ™zyk
Image

Types of supports and examples - Ansys Static Structural

Supports are used to represent parts that are not present in the model but are interacting with it. Supports help truncate the domain, which helps in efficiently obtaining numerically accurate results without modeling parts of the geometry that are not of primary interest. There are different types of support available, among which you need to choose the appropriate one for your analysis. Here are some of the common types of supports and their explanations: - **Fixed Support**: This type of support constrains all the degrees of freedom of the selected entity (body, face, or edge). It means that the entity cannot move or rotate in any direction. Fixed support is equivalent to applying zero displacement to all directions. Fixed support is useful for modeling rigid connections or supports that do not allow any movement. For example, you can use fixed support to model a bolted joint or a clamped beam. - **Displacement Support**: This type of support specifies a zero or non-zero displacemen
Image

How to define porosity (porous medium) in Ansys CFD (Fluent, CFX)

 To model porosity in ANSYS Fluent , you need to define the porous zone and the porous media properties in the setup. You can follow these steps: In the Fluent interface, go to the Cell Zone Conditions panel and select the zone that you want to make porous. Check the Porous Zone option and click Edit. In the Porous Zone panel, you can choose between two methods to specify the porous media resistance: the Superficial Velocity method or the Physical Velocity method. The Superficial Velocity method uses the superficial velocity (the velocity of the fluid if there were no porosity) to calculate the pressure drop across the porous zone. The Physical Velocity method uses the physical velocity (the velocity of the fluid inside the pores) to calculate the pressure drop across the porous zone. You can also choose between isotropic or anisotropic porosity, depending on whether the porosity is uniform or varies in different directions. Depending on the method and the type of porosity you choose,
Image

How to... fix "gui-domain-label: no domain selected" in Ansys Fluent and MEMERR in CFX

In today's post, we will deal with another error that may occur during the analysis. The error that is described below concerns Fluent and the wrong definition of user monitors that are displayed during simulation. These can be monitors concerning the average velocity in the domain volume, the values of the maximum temperatures of the solid domains, the average values of the heat transfer coefficient from the defined planes of the model, etc. Generally speaking, today's entry is about how to correctly define monitors and how to transfer them between subsequent analyzes. Example of "gui-domain-label" error in Fluent