πŸ’₯πŸ’₯πŸ’₯ Don't Block the Party: How a Marble Can Ruin Your Gas Station Trip

on

 Imagine you're pouring yourself a giant soda. Nice and fizzy, right? Now picture sticking a marble in the straw. Chaos! Here's what might happen to the gas pump in a similar situation:

1. **The Block Party:** The ball would get lodged in the nozzle, throwing a wrench (or should we say, a marble?) into the gas flow. The party's over for the smooth stream of gasoline.

2. **Fizzing Fury:**  Depending on the size of the marble and the gas pressure, things could get fizzy. The trapped gas might sputter out in spurts and stops, making refueling a frustrating tap dance.

3. **The Auto Shutoff Brigade:** Most gas pumps have shutoff mechanisms that kick in if the flow gets weird.  The little gremlins inside might think a rogue marble is a full tank and shut things down entirely.

4. **The Hissing Suspect:**  Even if the flow keeps going, the blockage from the marble could create a pressure change.  This might lead to some dramatic hissing, like the gas pump is whispering secrets about your questionable car maintenance habits. 

So, the short story is, don't put a marble in the gas nozzle. It's a recipe for frustration, fizzy messes, and possibly a grumpy gas station attendant. Just stick to pouring that delicious gasoline... into your car, of course. 

Comments

Post a Comment

Popular POSTS

Image

Quick Tip: How to fix Error: GENERAL-CAR-CDR in Ansys (Fluent)

 The error message Error: GENERAL-CAR-CDR: invalid argument [1]: improper list means that there is a problem with the scheme code or the UDF (user-defined function) in your case or data file . Some possible solutions are: Save the case and data file and try to reopen it. Reset the Fluent Setup tab and try opening the mesh. Remesh the geometry and reopen in Fluent. Change the material definition from “Solid” to “Fluid” in Design Modeler. Change the transient to steady if you are using evaporation-condensation as the phase interaction mechanism. Check the syntax of your UDF and make sure it follows the new rules in Fluent 6.2.16 or later. I hope this helps you resolve the error. If you need more assistance, please visit the Ansys Learning Forum or contact Ansys Support . Have a nice day! 😊 Sources: 1. smartadm.ru 2. cfd-online.com 3. forum.ansys.com 4. forum.ansys.com In Polish  BΕ‚Δ…d: GENERAL-CAR-CDR oznacza, ΕΌe wystΔ…piΕ‚ problem z kodem Scheme w programie Ansys Fluent. Scheme to jΔ™zyk
Image

Types of supports and examples - Ansys Static Structural

Supports are used to represent parts that are not present in the model but are interacting with it. Supports help truncate the domain, which helps in efficiently obtaining numerically accurate results without modeling parts of the geometry that are not of primary interest. There are different types of support available, among which you need to choose the appropriate one for your analysis. Here are some of the common types of supports and their explanations: - **Fixed Support**: This type of support constrains all the degrees of freedom of the selected entity (body, face, or edge). It means that the entity cannot move or rotate in any direction. Fixed support is equivalent to applying zero displacement to all directions. Fixed support is useful for modeling rigid connections or supports that do not allow any movement. For example, you can use fixed support to model a bolted joint or a clamped beam. - **Displacement Support**: This type of support specifies a zero or non-zero displacemen
Image

How to define porosity (porous medium) in Ansys CFD (Fluent, CFX)

 To model porosity in ANSYS Fluent , you need to define the porous zone and the porous media properties in the setup. You can follow these steps: In the Fluent interface, go to the Cell Zone Conditions panel and select the zone that you want to make porous. Check the Porous Zone option and click Edit. In the Porous Zone panel, you can choose between two methods to specify the porous media resistance: the Superficial Velocity method or the Physical Velocity method. The Superficial Velocity method uses the superficial velocity (the velocity of the fluid if there were no porosity) to calculate the pressure drop across the porous zone. The Physical Velocity method uses the physical velocity (the velocity of the fluid inside the pores) to calculate the pressure drop across the porous zone. You can also choose between isotropic or anisotropic porosity, depending on whether the porosity is uniform or varies in different directions. Depending on the method and the type of porosity you choose,
Image

πŸ’₯πŸ’₯πŸ’₯ How to model in PrePoMAX ?

PrePoMax is a freeware pre- and postprocessor for open-source Finite Element Analysis solver CalculiX 1 . It offers a user-friendly GUI and supports many features provided by the CalculiX solver. To model in PrePoMax, you need to follow these general steps: Create or import a geometry using the Geometry menu 2 . Generate a mesh using the Mesh menu 2 . Define the FE model using the Model , Property , Interaction , Initial Condition , and Step menus 2 . Export the input file for CalculiX using the File menu 2 . Run the analysis using the Tools menu 2 . Import the results file and visualize the output using the View menu 2 . You can find more detailed instructions and examples in the PrePoMax documentation 1 and video tutorials 1 . I hope this helps you get started with PrePoMax. 😊 The official PrePoMax website 1 has a section on documentation, where you can download the PrePoMax manual in PDF format. The manual covers the basic features and workflow of PrePoMax, as well as some